Recent questions and answers in Engineering

Recent questions and answers in Engineering

What went wrong with sonarscanner?

Paul Warnick answered Jan 4

by Paul Warnick

8.3k points

1 answer

0 votes

161k views

Name four sources of heat commonly used for hydronic heating systems? 1) Natural gas 2) Electricity 3) Oil 4) Solar energy

Neka answered Jan 4

by Neka

8.6k points

1 answer

2 votes

92.5k views

Which of the following best describes HCPS Level II codes? A) The codes have five characters: numbers, letters, or a combination of both. B) The codes have six characters, including two initial letters

Alex Skorkin answered Jan 4

by Alex Skorkin

8.0k points

1 answer

4 votes

53.7k views

What device can be installed to protect a hot water boiler from low water level? a) Pressure relief valve b) Flow switch c) Low water cut-off d) Expansion tank

NotMyName answered Jan 4

8.0k points

1 answer

1 vote

234k views

The technique for joining copper water pipes is called

FLGMwt answered Jan 4

by FLGMwt

7.7k points

1 answer

5 votes

32.6k views

When a repair station makes a major repair to an applicance, the repair may be recorded on the tag attached to the product or on the customer's work order. in either case, the document used must include

Chronikum answered Jan 4

7.8k points

1 answer

0 votes

72.8k views

What is the desired air gap between the ABS wheel speed sensor and the exciter ring? a) 1/4" (6.25mm) b) 3/8" (9.5mm) c) Air gap is not critical d) As close as possible

Vlad Hilko answered Jan 4

8.4k points

1 answer

3 votes

48.2k views

ACSR stands for (a) Aluminum-clad steel conductor (b) Aluminum conductor steel supported (c) Aluminum conductor steel reinforced

Tien Nguyen answered Jan 4

7.0k points

1 answer

0 votes

111k views

1. Calculate the surface deflection under the centre of a tyre (a = 152 mm, p = 552 kPa) for a 305 mm pavement having a 345 MPa modulus and subgrade modulus of 69 MPa from two-layer theory. Also calculate

Idan Moshe answered Jan 4

8.0k points

1 answer

2 votes

123k views

The heat resistance, R, for convection heat transfer on the inside surface of a wall is: a)R = R1 + R2 + R3 b)R = L / (K A) c)R = 1 / (h A) d)1/R = 1/R1 + 1/R2 + 1/R3

Waleed Asender answered Jan 4

by Waleed Asender

8.1k points

1 answer

0 votes

163k views

If you remove the plug from the tube, which way will the water flow? In a complete sentence, explain why.

Kavindu Dissanayake answered Jan 4

by Kavindu Dissanayake

8.2k points

1 answer

2 votes

13.2k views

Which of the following clamps has a.c-shape and a threaded metal shaft fitted with a shoe that is designed to swivel? select one: a. pipe clamp b. c-clamp c. hand screw clamp d. bar clamp

Rubie answered Jan 4

by Rubie

8.0k points

1 answer

0 votes

192k views

What is the term for an elevated platform projecting from the wall of a building and enclosed by a railing or parapet? Options: Option 1 - Terrace Option 2 - Patio Option 3 - Balcony Option 4 - Veranda

FloIancu answered Jan 4

8.7k points

1 answer

2 votes

163k views

If a calcification with a CT number of 300 appears pure white on an image, which of the following could be the window width and window level selected? 1) wl = 0, ww = 500 2) wl = 300, ww = 500 3) wl =

Priv answered Jan 4

by Priv

7.9k points

1 answer

3 votes

176k views

When working with cables and a pull system, it is acceptable to use ___. 1) Nylon ropes 2) Steel cables 3) Rubber bands 4) Paper clips

Stefanobaldo answered Jan 4

by Stefanobaldo

8.6k points

1 answer

1 vote

228k views

What are the three types of service classes on International main cabin service?

Autronix answered Jan 4

7.9k points

1 answer

2 votes

194k views

At what angle do you connect your glad hand connections to the trailer?

Branden Barber answered Jan 4

by Branden Barber

7.7k points

1 answer

4 votes

174k views

To land, an aircraft's __ must be reduced safely below its __, as its lift is reduced to levels less than its __.

Rdiz answered Jan 4

by Rdiz

7.8k points

1 answer

3 votes

59.7k views

Calculate shear force on a beam if the stress 354.00 psi at a depth of d from the top surface of the beam shown. Assume d 4 in, b-8 in, and h-11 in

Mohammad Dohadwala answered Jan 4

by Mohammad Dohadwala

8.2k points

1 answer

5 votes

84.6k views

A series of related messages in a newsgroup or email is called a(n)

Derek Lawrence answered Jan 4

by Derek Lawrence

8.5k points

1 answer

0 votes

140k views

To see more, click for all the questions in this category.

Search QAmmunity.org