menu
Qammunity
Login
Register
My account
Edit my Profile
Private messages
My favorites
Ask a Question
Questions
Unanswered
Tags
Categories
Ask a Question
Technician A says you should place the air ratchet setting to clockwise to loosen a fastener. Technician B says a fastener must be set to the proper torque after using an air ratchet. Who is correct?
asked
May 11, 2021
62.0k
views
4
votes
Technician A says you should place the air ratchet setting to
clockwise to loosen a fastener. Technician B says a fastener
must be set to the proper torque after using an air ratchet. Who
is correct?
Engineering
college
Kiwiupover
asked
by
Kiwiupover
7.6k
points
answer
comment
share this
share
0 Comments
Please
log in
or
register
to add a comment.
Please
log in
or
register
to answer this question.
1
Answer
3
votes
I think it’s b sry if I’m wrong tho
Mike Kellogg
answered
May 16, 2021
by
Mike Kellogg
8.7k
points
ask related question
comment
share this
0 Comments
Please
log in
or
register
to add a comment.
← Prev Question
Next Question →
Related questions
asked
Aug 15, 2020
194k
views
Two technicians are discussing torque wrenches. Technician A says that a torque wrench is capable of tightening a fastener with more torque than a conventional breaker bar or ratchet. Technician B says
Flyer
asked
Aug 15, 2020
by
Flyer
8.2k
points
Physics
high-school
2
answers
2
votes
194k
views
asked
May 19, 2021
206k
views
Two technicians are discussing hand tool use. Technician A says that a 6-point wrench is easier to use in tight places than a 12-point. Technician B says that a ratchet is used to loosen fasteners that
Ajaristi
asked
May 19, 2021
by
Ajaristi
8.0k
points
Engineering
college
2
answers
2
votes
206k
views
asked
Jun 16, 2020
34.4k
views
Technician A says that for best results, loosen the fastener immediately after spraying it with penetrating oil. Technician B says that rusted fasteners may be loosened by tapping with a hammer. Which
MFW
asked
Jun 16, 2020
by
MFW
7.1k
points
Physics
high-school
1
answer
3
votes
34.4k
views
Ask a Question
Welcome to QAmmunity.org, where you can ask questions and receive answers from other members of our community.
9.4m
questions
12.2m
answers
Other Questions
A piston-cylinder device fitted with stops in the cylinder walls contains 2.1 kg of water initially at 150 kPa and 30 °C. Heat is transferred to the system until the final temperature reaches 250 °C. The
A water towers lowest point is 405 ft and the main line is 6 feet below the ground. The ground elevation is at 276 ft. The main line travels 2.9 miles. The pipe will travel through the following flanged
An activated sludge plant is being designed to handle a feed rate of 0.438 m3 /sec. The influent BOD concentration is 150 mg/L and the cell concentration (MLVSS) is 2,200 mg/L. If you wish to operate the
A car has an initial speed of 10 m/s. It then undergoes a constant acceleration of 0.05 m/s^2 over a distance of 5 km. Determine: a) The car final speed. b) The time needed to travel the 5 km.
In solid motors, HTPB and PBAN are two common types of plasticizers. a) True b) False
Twitter
WhatsApp
Facebook
Reddit
LinkedIn
Email
Link Copied!
Copy
Search Qammunity