Recent questions in Engineering

Question

How is the tubular type jack stand locked? A. By means of a steel pin that is inserted into a hole in the tube. B. By means of a toothed section, that is locked with a cam. C. By means of thread and swivel.

Whatwhatwhat asked Dec 3, 2024

by Whatwhatwhat

7.4k points

1 answer

2 votes

32.6k views

T/F: the most common causes of deck collapse are ledgers that pull away from the band joists of home and buildings

LeoHorie asked Dec 3, 2024

by LeoHorie

7.3k points

1 answer

0 votes

33.6k views

The triangle cut ventilation hole provides the least reliable information of conditions beneath the roof. Select one: True False

Kerline asked Dec 3, 2024

by Kerline

8.0k points

1 answer

1 vote

202k views

For choosing a method's parameter types and/or return types, when might you prefer to use an object to bundle together data rather than a list or array (E.g. like Coord with it's two fields) ? Alternatively,

Adam Schiavone asked Dec 3, 2024

by Adam Schiavone

8.1k points

1 answer

0 votes

133k views

What is multiple lift rigging, or Christmas treeing? 1) A method used in construction to lift multiple objects simultaneously 2) A technique used in rock climbing to ascend multiple pitches 3) A term used

Tutts asked Dec 3, 2024

by Tutts

7.1k points

1 answer

1 vote

48.7k views

Consider the casual DT-LTI system defined by the following LCCDE: y[n]−0.7y[n−1]=x[n]. Derive on paper the response of the system (y[n]paper ) to the input signal x[n]=δ[n−1].

Bilal Akbar asked Dec 3, 2024

by Bilal Akbar

7.8k points

1 answer

4 votes

56.9k views

The inspector is required to report on: The approximate depth of insulation, where visible

Jacek Dominiak asked Dec 3, 2024

by Jacek Dominiak

8.3k points

1 answer

0 votes

148k views

Water is run through a hydraulic turbine at a rate of 11,500 L/min from a 160-m-high reservoir and produces 250 kW of shaft power. What is the efficiency of this turbine?

Numan Tariq asked Dec 3, 2024

by Numan Tariq

8.0k points

1 answer

3 votes

72.0k views

Name the three major assemblies that make up a disc brake.

Travis asked Dec 3, 2024

by Travis

8.0k points

1 answer

3 votes

189k views

Which would constitute the last step in a central-fan cooling control sequence? A. During the cooling season, when the home's air temperature rises above a predefined setpoint, the room thermostat calls

Rika asked Dec 3, 2024

by Rika

8.9k points

1 answer

3 votes

13.7k views

The overvoltage control automatically protects the generator system when excessive voltage is present by?

Jay Jeong asked Dec 3, 2024

by Jay Jeong

8.0k points

1 answer

1 vote

205k views

What is used to inflate the 25 man life raft?

Comte asked Dec 3, 2024

by Comte

7.8k points

1 answer

3 votes

206k views

P-factor is one of the forces that causes the airplane to _____

Michal Krasny asked Dec 3, 2024

by Michal Krasny

8.6k points

1 answer

2 votes

179k views

What would happen to the initial velocity of penicillinase if the concentration of substrate were increased?

Randall Goodwin asked Dec 3, 2024

by Randall Goodwin

7.4k points

1 answer

2 votes

147k views

How are the DME Radial Waypoints displayed in the FMS (Using the ARINC 424)?

Xdrone asked Dec 3, 2024

by Xdrone

8.4k points

1 answer

3 votes

81.1k views

Cross sequential design advantages (2)

Zag asked Dec 3, 2024

by Zag

8.4k points

1 answer

0 votes

57.4k views

ADIRS PANEL: How long does a fast alignment take to occur?

Quang Van asked Dec 3, 2024

by Quang Van

8.4k points

1 answer

2 votes

20.2k views

Under a typical architect-consultant agreement, which of the following is true of the consultant's work and standard of care? 1) The consultant is responsible for maintaining the highest level of professional

Hardik Vasani asked Dec 3, 2024

by Hardik Vasani

7.6k points

1 answer

4 votes

37.6k views

Write notes on hard and soft timing constraints in real time systems

Brian Ensink asked Dec 3, 2024

by Brian Ensink

7.1k points

1 answer

4 votes

115k views

When a driver leaves BC using BC PLATES: a. They must surrender the plates at the border b. The plates can be kept as souvenirs c. The plates must be returned to the licensing office d. The plates are

Casey Chow asked Dec 3, 2024

by Casey Chow

8.5k points

1 answer

0 votes

4.4k views

Page:

« prev
1
...
194
195
196
197
198
199
200
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions