Recent questions in Engineering

Question

The ____________________ give a tire its grooved surface.

Adrian Russell asked Dec 6, 2024

by Adrian Russell

9.2k points

1 answer

5 votes

130k views

The corrosion control program established by the what is an ALL HANDS participation concept?

Adelphus asked Dec 6, 2024

by Adelphus

7.8k points

1 answer

0 votes

207k views

What is the way to tell if a vehicle is following you too closely? 1) The vehicle is tailgating you 2) The vehicle is driving at a safe distance 3) The vehicle is using turn signals 4) The vehicle is maintaining

Michael Klemm asked Dec 6, 2024

by Michael Klemm

7.8k points

1 answer

5 votes

219k views

How frequently should the Health Indicator (HI) be reset during a flight? a) Every 5 minutes b) Every 10 minutes c) Every 15 minutes d) Every 20 minutes

Oleg Polezky asked Dec 6, 2024

by Oleg Polezky

8.2k points

1 answer

4 votes

62.3k views

An upright stone slab or pillar with a carved or inscribed surface, used as a monument or marker, or as a commemorative tablet in the face of a building. a) Obelisk b) Cenotaph c) Plinth d) Stela

Centril asked Dec 6, 2024

by Centril

8.4k points

1 answer

3 votes

159k views

You wish to do a standard rate 1 turn, which is at 18deg AOB. What would be the TAS? A) (X * 10%) + 7 = 18 —> X = 110 KTS B) (X * 15%) + 5 = 18 —> X = 120 KTS C) (X * 5%) + 12 = 18 —> X = 120 KTS D) (X

Sevgi asked Dec 6, 2024

by Sevgi

8.3k points

1 answer

3 votes

141k views

Silver brazing is done best with joints designed to allow for what?

DenseCrab asked Dec 6, 2024

by DenseCrab

8.2k points

1 answer

2 votes

87.3k views

Odbrai 1. In some sets of commercial drawings, the site For More plans are called _________. --- a. civil drawings b. commercial drawing c. layout drawings D elevation drawings

Matt Slavicek asked Dec 6, 2024

by Matt Slavicek

8.5k points

1 answer

0 votes

14.3k views

What is the possible cause for a system that fails to hold a vacuum after the evacuation process? 1) Has a restriction. 2) May contain moisture. 3) May have a leak. 4) B and C above.

Priyanth asked Dec 6, 2024

by Priyanth

8.7k points

1 answer

2 votes

80.9k views

Which of the following boats is required to have a Type IV (throwable) Personal Floatation Device on board under USCG regulations?

Sasynkamil asked Dec 6, 2024

by Sasynkamil

8.1k points

1 answer

1 vote

127k views

Who designates the ABO Surveillance Program Manager and via what document?

Rotsor asked Dec 6, 2024

by Rotsor

7.8k points

1 answer

4 votes

90.2k views

Engine EGT Limits - Takeoff ( ___ min)

ATrubka asked Dec 6, 2024

by ATrubka

9.2k points

1 answer

2 votes

51.8k views

16) HDPE stands for ______. A) high-density polyethylene. B) hot-dipped polyethylene. C) high-dose polyethylene. D) highly-diffuse polyethylene.

Seanalltogether asked Dec 6, 2024

by Seanalltogether

8.1k points

1 answer

5 votes

148k views

Which of the following shares have the right to vote? 1) unissued shares 2) treasury shares 3) outstanding shares 4) liquidated shares

Kirk Broadhurst asked Dec 6, 2024

by Kirk Broadhurst

8.1k points

1 answer

0 votes

143k views

That part of the brake system which is designed to cause the brakes on all cars in a train to apply equally at the same time is the ________. 1) Brake pedal 2) Brake fluid 3) Brake master cylinder 4) Brake

Ouarzy asked Dec 6, 2024

by Ouarzy

8.1k points

1 answer

1 vote

169k views

What are some features of an UNATTENDED facility design?

Weicheng asked Dec 6, 2024

by Weicheng

8.4k points

1 answer

4 votes

14.4k views

Which lining does most of the braking on a dual-servo brake? a. Front (forward facing) B. Rear (rearward facing =) c. Depends on the speed of the vehicle

Vmorph asked Dec 6, 2024

by Vmorph

8.1k points

1 answer

2 votes

128k views

Design the inverter circuit in Fig. 1.7 to provide VOH = 1.0 V, VOL = 50 mV, and so that the current drawn from the supply in the low-output state is 30 µA. The transistor has Vt = 0.35 V, μnCox = 540

XTF asked Dec 6, 2024

by XTF

7.3k points

1 answer

4 votes

25.9k views

The plates for the shell of a pressure vessel are usually formed with the rolling direction: a) diagonal to the length b) along the length c) in the least favourable direction d) around the circumference

Qi Luo asked Dec 6, 2024

by Qi Luo

8.5k points

1 answer

2 votes

231k views

What must the contractor do if they believe the architect's minor change of work will affect time or cost?

Avi L asked Dec 6, 2024

by Avi L

7.9k points

1 answer

2 votes

114k views

Page:

« prev
1
...
175
176
177
178
179
180
181
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions