Recent questions in Engineering

Question

For Aircraft operated in an air transport service for entire period of flight at cabin-pressure- altitudes above 13000 feet ASL, a period of flight of not less than ____ ____, all persons on board the

Peewee asked Dec 10, 2024

by Peewee

7.2k points

1 answer

1 vote

166k views

Motors with built-in thermal production must have external overload devices?

Csonuryilmaz asked Dec 10, 2024

by Csonuryilmaz

7.9k points

1 answer

5 votes

168k views

What does the helm command "shift the rudder" mean? a) Gradual change in rudder position b) Quickly move the rudder to the opposite side c) Steady rudder amidships d) Alternate between port and starboard

Artiom Gourevitch asked Dec 10, 2024

by Artiom Gourevitch

8.0k points

1 answer

0 votes

69.1k views

Where are natural gas shut offs located?

Unpix asked Dec 10, 2024

by Unpix

8.7k points

1 answer

5 votes

29.6k views

Which of the following is an empty set: A. Ω(g(n)) ∩σ(g(n)) B. Ω(g(n)) ∩ω(g(n)) C. 0(g(n)) ∩σ(g(n)) D. Ω(g(n)) ∩0(g(n)) A) D B) A C) B D) C

Isadora asked Dec 10, 2024

by Isadora

7.7k points

1 answer

3 votes

205k views

in a half wave rectification process; when no load was connected the output was observed to be 220 v and when a load of 10 kq was connected the output was 210. what is the % regulation of the rectifier?

Rashwan L asked Dec 10, 2024

by Rashwan L

8.3k points

1 answer

1 vote

135k views

You are flying into a 20KT HW on T/O. You do a 180deg turn. What will happen to IAS, TAS and G/S? a) IAS, TAS, and G/S will all remain the same. b) IAS will decrease, TAS and G/S will increase. c) IAS,

Gsaslis asked Dec 10, 2024

by Gsaslis

7.2k points

1 answer

2 votes

166k views

- Create a program(forkchildren.c) that will fork off two children. - One child will run the "Is -I" command. - The other will run "cat forkchildren.c". - The main program will wait for the children to

Dan Alboteanu asked Dec 10, 2024

by Dan Alboteanu

7.6k points

1 answer

2 votes

14.4k views

What were the hilt and crosspiece inlaid with

Kronosjt asked Dec 10, 2024

by Kronosjt

8.3k points

1 answer

4 votes

24.2k views

Which object should be used to build a boat? 1) Flower petals 2) Wood 3) Rocks 4) D) Cloth

Ofir G asked Dec 10, 2024

by Ofir G

8.0k points

2 answers

5 votes

214k views

Sharing information with key international partners supports which Design for Maritime Superiority Line of Effort?

Antonicg asked Dec 10, 2024

by Antonicg

8.1k points

1 answer

0 votes

183k views

Except in an emergency (or a medical patient under proper care), no pilot of an aircraft may allow a person...

Rahul Banerjee asked Dec 10, 2024

by Rahul Banerjee

7.9k points

1 answer

1 vote

45.3k views

It is important before welding and hot work to remove coatings along the line of the world such as _______ to prevent the release of toxins? 1) paint 2) rust 3) dirt 4) grease

Albertoperdomo asked Dec 10, 2024

by Albertoperdomo

8.3k points

1 answer

2 votes

79.7k views

Which of the following resources does the National Institute of Standards and Technology (NIST) provide to organizations? A. Reference materials B. Security tools C. Industrial configurations D. Measurement

Jelder asked Dec 10, 2024

by Jelder

7.3k points

1 answer

2 votes

11.9k views

Which of the following situations require the use of safety shoes with toe protection? Select all that apply and then click DONE. 1) Working around heavy equipment 2) Handling equipment that could drop

Rachit Mishra asked Dec 10, 2024

by Rachit Mishra

7.9k points

1 answer

2 votes

148k views

End frames of scaffolds and ladders in elevator shafts shall have rungs and steps spaced not less than 6 inches (15 cm) apart or more than 16-1/2 inches (41 cm) apart, as measured along the ladder side

Dennis Ich asked Dec 10, 2024

by Dennis Ich

8.6k points

1 answer

2 votes

181k views

Which of the following is a distinguishing characteristic of a pressure tank railcar? a. Visible valves and piping b. An enclosed dome on the top of the tank c. A full-perimeter structural frame d. External

Ghollah Kioko asked Dec 10, 2024

by Ghollah Kioko

8.0k points

1 answer

0 votes

234k views

What is the recommended shape of a C-5 escape slide repair patch? 1) Circular 2) Rectangular 3) Triangular 4) Irregular

Tomasz Elendt asked Dec 10, 2024

by Tomasz Elendt

7.5k points

1 answer

5 votes

220k views

Legally, a renter has the upper hand based on what is written on the lease, even when there was a verbal agreement only to conditions such as no penalty if a payment is a couple of days late. a-true b-false

Dhagz asked Dec 10, 2024

by Dhagz

8.9k points

1 answer

5 votes

55.4k views

Closed-head drums usually have bungs of what size? 1) 1 inch 2) 2 inch 3) 3 inch 4) 4 inch

Dushyantp asked Dec 10, 2024

by Dushyantp

8.5k points

1 answer

5 votes

106k views

Page:

« prev
1
...
146
147
148
149
150
151
152
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions