Recent questions in Engineering

Question

If doing a pre-trip air brake inspection, which of the below would be acceptable pressure levels for the air supply valve and park control valve to pop out at? a) 30 psi b) 40 psi c) 50 psi d) 60 psi

Katfang asked Aug 11, 2024

by Katfang

7.8k points

1 answer

1 vote

149k views

The hybridization of the carbon atoms in the molecule represented above can be described as A sp B sp2 C sp3 D dsp2 E d2sp

Jerrytim asked Aug 11, 2024

by Jerrytim

8.4k points

1 answer

0 votes

235k views

Working with MongoDB from a program Introduction: This assignment gives you a brief introduction to connecting to a MongoDB database from a Python program using pymongo. The database design is denormalized

Seedhead asked Aug 11, 2024

by Seedhead

8.2k points

1 answer

2 votes

227k views

Which of the following would be the best cost driver for the assembling cost pool? 1) Number of product lines. 2) Number of parts. 3) Number of orders. 4) Amount of square footage.

Bhaskar Dabhi asked Aug 11, 2024

by Bhaskar Dabhi

8.3k points

1 answer

0 votes

200k views

What determines exit route types and quantities?

Dan Sabin asked Aug 11, 2024

by Dan Sabin

8.6k points

1 answer

4 votes

183k views

What tool could you use to separate magnetite from gravel?

Attila Zobolyak asked Aug 11, 2024

by Attila Zobolyak

7.7k points

1 answer

1 vote

73.7k views

If powder actuated tools misfire, hold it in operating position for at least _______ seconds before re-firing.

Lucas Vazquez asked Aug 11, 2024

by Lucas Vazquez

8.0k points

1 answer

5 votes

209k views

What allows the brake caliper to be self-adjusting?

MrSimpleMind asked Aug 11, 2024

by MrSimpleMind

7.8k points

1 answer

5 votes

210k views

What is the purpose of performing the t-spine rotation drill from the quadruped position with one supporting arm on the ground? A) Increase Lumbar Flexion B) Enhance Hip Mobility C) Improve Shoulder Stability

Shreyansh Sharma asked Aug 11, 2024

by Shreyansh Sharma

7.8k points

1 answer

5 votes

77.3k views

What is wrong with V-Autos method based system?

Rameswar Prasad asked Aug 11, 2024

by Rameswar Prasad

8.3k points

1 answer

2 votes

205k views

Which of the following requires an endorsement on your CDL? a) Operating a motorcycle b) Driving a passenger bus c) Transporting hazardous materials d) All of the above

Arzhh asked Aug 11, 2024

by Arzhh

8.5k points

1 answer

4 votes

38.6k views

What are the alternate takeoff aerodrome requirements for a 705 Operation?

Rafiul asked Aug 11, 2024

by Rafiul

8.6k points

1 answer

0 votes

202k views

What could produce a twisted mainshaft in a standard transmission? a) Improper driveline operating angles b) Not using the clutchWhen shifting c) Shock loads d) Excessive mainshaft gear tolerances

Jakobhans asked Aug 11, 2024

by Jakobhans

8.1k points

1 answer

4 votes

120k views

Name the inputs to the Trane defrost control.

CarlJ asked Aug 11, 2024

by CarlJ

8.1k points

1 answer

0 votes

127k views

What is the default administrative distance of OSPF route? 1) 90 2) 100 3) 110 4) 120

Maddalena asked Aug 11, 2024

by Maddalena

8.5k points

1 answer

5 votes

138k views

What are two major advantages of rear entry? A) Improved aerodynamics and fuel efficiency B) Enhanced passenger safety and visibility C) Easier access and increased cargo space D) Better maneuverability

Pisswillis asked Aug 11, 2024

by Pisswillis

9.1k points

1 answer

5 votes

79.8k views

Protection standards limit work place unprotected exposure of Hexamethylene Diisocyanates or Toluene Diisocyanate to a concentration of how many PPM averaged over an 8-hour period?

SimplyPhy asked Aug 11, 2024

by SimplyPhy

8.3k points

1 answer

5 votes

53.1k views

Which of the following is true about hubs? a. Devices on a hub have to share the available bandwidth. b. they can operate in full-duplex and half-duplex mode. c. they maintain a table of MAC addresses.

Tschm asked Aug 11, 2024

by Tschm

8.1k points

1 answer

4 votes

1.3k views

What is a structure that is accessory and incidental to the dwelling(s) and is located on the same lot?

Daniel Medina asked Aug 11, 2024

by Daniel Medina

7.4k points

1 answer

4 votes

227 views

The point at which a metal's behavior changes from elastic to plastic (onset of permanent deformation) is referred to as: a. Yield strength b. Ultimate tensile strength c. Modulus of elasticity d. Young's

Gassa asked Aug 11, 2024

by Gassa

7.0k points

1 answer

2 votes

107k views

Page:

« prev
1
...
990
991
992
993
994
995
996
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions