Recent questions in Engineering

Question

How many full sheets of 4' x 8' plywood are needed for a rectangular subfloor that is 32' x 72'? (do not count waste) a) 12 sheets b) 16 sheets c) 18 sheets d) 24 sheets

Ahmad Ronagh asked Aug 12, 2024

by Ahmad Ronagh

8.1k points

1 answer

0 votes

227k views

(Airframe speed limitations) Landing gear emergency operating:

Theatlasroom asked Aug 12, 2024

by Theatlasroom

7.9k points

1 answer

5 votes

95.0k views

Are the brackets [ ] ALWAYS needed on BOTH sides of the equation?

Batatop asked Aug 12, 2024

by Batatop

8.0k points

1 answer

2 votes

69.9k views

Employees who note defects or any unusual conditions that would delay or make unsafe the movement of trains must

TechnicalTophat asked Aug 12, 2024

by TechnicalTophat

7.9k points

1 answer

5 votes

39.7k views

A brick or other masonry unit laid horizontally in a wall with the longer edge exposed or parallel to the surface. Options: Option 1: Header Option 2: Stretcher Option 3: Soldier Option 4: Rowlock

Jakub Kania asked Aug 12, 2024

by Jakub Kania

8.6k points

1 answer

2 votes

47.8k views

A type of system that is capable of self-maintenance within a larger context or environment, and in which the influence of internal and external environments are keenly recognized, is best called a(n):

Internet Engineer asked Aug 12, 2024

by Internet Engineer

9.0k points

1 answer

0 votes

71.8k views

On the SMEE-type subway car, the PROPER position of the brake handle when operating normally over the road is

Xmaestro asked Aug 12, 2024

by Xmaestro

8.1k points

1 answer

5 votes

12.2k views

In the event of _________ due to a hard landing or crash loads, red bands appear on the ourside of the VLEA housing.

Gcores asked Aug 12, 2024

by Gcores

8.1k points

1 answer

2 votes

48.0k views

What are the factors associated with successful CQI applications?

Dotmido asked Aug 12, 2024

by Dotmido

8.6k points

1 answer

2 votes

107k views

What must the technician use to remove excess flux after completing a solder joint?

Rajiv A asked Aug 12, 2024

by Rajiv A

8.5k points

1 answer

5 votes

173k views

Compute the distance between the positions of the first and last zero element in the given array. For example, if the array is 3 0 1 0 4 9 5 0 6 your algorithm should yield 7 - 1 = 6.

Marse asked Aug 12, 2024

by Marse

8.8k points

1 answer

2 votes

192k views

What is the 5-degree cone representing in ___vision? 1) Only 3 2) Only 5 3) Both 3 and 5 4) Neither 3 nor 5

Fahad Abid asked Aug 12, 2024

by Fahad Abid

9.4k points

1 answer

2 votes

7.7k views

True or false respirators are never needed when using oxyfuel

Clearscreen asked Aug 12, 2024

by Clearscreen

8.3k points

1 answer

0 votes

155k views

The two outer bends of a Three Point Saddle must NEVER add up to the single bend in the center. a. false. b. true

Kuro asked Aug 12, 2024

by Kuro

8.7k points

1 answer

0 votes

208k views

It is possible to meet dispatch requirements yet have a minimum landing distance (based on expected braking action) greater than the landing distance available. Can you depart?

Phill asked Aug 12, 2024

by Phill

8.1k points

1 answer

2 votes

35.5k views

This signal requires the train operator to ?

Grace Huang asked Aug 12, 2024

by Grace Huang

8.2k points

1 answer

3 votes

38.5k views

What is the first step in preparing for bonding the brackets? 1) Cleaning the surface 2) Applying adhesive 3) Positioning the brackets 4) Securing the brackets with screws

Efeyc asked Aug 12, 2024

by Efeyc

8.8k points

1 answer

5 votes

23.8k views

What does a drip edge do? a. Stops ice damming b. Protects the parts below it like the fascia, siding, etc. c. Protects the ridge vents d. Prevents cupping of shingles

Xxddoo asked Aug 12, 2024

by Xxddoo

7.9k points

1 answer

3 votes

15.8k views

Which of the following is said by transmission OEMs to cause most transmission bearing failures? a) lack of lubrication b) improper shifting c) operation on rough highways d) dirt

Glenn Sampson asked Aug 12, 2024

by Glenn Sampson

8.0k points

1 answer

3 votes

102k views

A stationary design line is a guide to where all lengths are directed and is stable? 1) True 2) False

Robert Balent asked Aug 12, 2024

by Robert Balent

7.0k points

1 answer

3 votes

216k views

Page:

« prev
1
...
984
985
986
987
988
989
990
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions