Recent questions in Engineering

Question

What are the different engine indications used for trimming a turbine engine?

Mike At Bookup asked Aug 13, 2024

by Mike At Bookup

8.3k points

1 answer

5 votes

160k views

Predicted TLC is 3.6. The actual is 4.2. What does that mean? What do you expect the RV to be?

Prashant Shukla asked Aug 13, 2024

by Prashant Shukla

7.9k points

1 answer

4 votes

74.0k views

By the time the police arrived, the entire truck burst into flames, it is fueled by the hundreds of gallons of gasoline on board. A. NO CHANGE B. it was C. they found it D. OMIT the underlined portion

JoshWillik asked Aug 13, 2024

by JoshWillik

8.6k points

1 answer

1 vote

76.1k views

A beam pocket/wall notch allows the top of the girder to be flush with the top of the sill plate. It should be large enough to allow ________ clearance at the sides and ends of the beam for ventilation?

Segalaj asked Aug 13, 2024

by Segalaj

7.1k points

1 answer

0 votes

138k views

In addition to MIL-STD-188141B ALE, the AN/PRC-150(C) includes which type of third generation HF Link Automation?

Bouki asked Aug 13, 2024

by Bouki

8.1k points

1 answer

5 votes

11.2k views

The type of signal used at congested stations to close-in trains is known as a ______ signal

Arshan asked Aug 13, 2024

by Arshan

7.3k points

1 answer

1 vote

185k views

GMAW - power supplies are __________ type machines while SMAW power supplies are __________ type. a. Constant-voltage constant-potential, constant-current drooping arc voltage. b. Constant-current drooping

Himanshu Patel asked Aug 13, 2024

by Himanshu Patel

8.2k points

1 answer

4 votes

29.6k views

A device that performs a basic operation on electrical signals is called a ______.

MaxZ asked Aug 13, 2024

by MaxZ

7.4k points

1 answer

4 votes

4.5k views

A hole is being drilled in a 20 mm thick block of magnesium alloy with a 15 mm drill with a point angle of 118ᵒ at a feed of 0.1 mm/rev. The spindle is running at 500rpm. Calculate the material removal

Discort asked Aug 13, 2024

by Discort

8.8k points

1 answer

5 votes

214k views

The overall strategy of hazard control is called? a) Risk assessment b) Liability evaluation c) Negligence prevention d) Mitigation

Wypul asked Aug 13, 2024

by Wypul

7.7k points

1 answer

2 votes

235k views

a pressure gage connected to a tank reads 50 psi at a location where the barometric reading is 29.1 in hg. determine the absolute pressure in the tank. take

Iamkoa asked Aug 13, 2024

by Iamkoa

7.5k points

1 answer

0 votes

209k views

In which direction should the adjusting nut be turned to tighten the brakes?

Navela asked Aug 13, 2024

by Navela

8.1k points

1 answer

4 votes

93.6k views

What does a high grade number mean for a fastener?

MojoFilter asked Aug 13, 2024

by MojoFilter

7.8k points

1 answer

5 votes

145k views

Describe the weights of the M4 Rifle without mgazine and sling, and with sling and loaded 30 round magazine.

RidiX asked Aug 13, 2024

by RidiX

8.1k points

1 answer

3 votes

147k views

A wood sill is typically used to connect the top of the foundation to the wood floor system above.

Hoffmania asked Aug 13, 2024

by Hoffmania

7.7k points

1 answer

4 votes

11.3k views

QUESTION 1 Which is a feature of RISC not CISC? Highly pipelined Many addressing modes Multiple cycle instructions Variable length instructions. 10 points QUESTION 2 Supervised learning assumes prior knowledge

Don Srinath asked Aug 13, 2024

by Don Srinath

7.7k points

1 answer

3 votes

132k views

You are using a stand-assist mechanical lift. Which is unsafe? a. the person is holding the lift's hand grips b. the person's feet are on the footplate c. the lifts base is narrow when lifting d. the persons

SebCorbin asked Aug 13, 2024

by SebCorbin

9.1k points

1 answer

1 vote

34.6k views

If you are making a turn and your engine shuts off in the middle of a busy intersection:

James Elder asked Aug 13, 2024

by James Elder

7.6k points

1 answer

4 votes

219k views

What is the first step when parallel parking? A) Position vehicle 2 to 3 feet and parallel to to vehicle you plan to park behind B) Turn on signal to communicate intentions to vehicles behind C) Slowly

JLearner asked Aug 13, 2024

by JLearner

8.8k points

1 answer

2 votes

9.9k views

When parallel parking, the space you choose to park in should be at least as long as what? 1) The length of the car 2) The width of the car 3) The height of the car 4) The weight of the car

Lasaun asked Aug 13, 2024

by Lasaun

9.0k points

1 answer

1 vote

138k views

Page:

« prev
1
...
972
973
974
975
976
977
978
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions