Recent questions in Engineering

Question

What are the two main advantages of a dual ignition system? A. Increased fuel efficiency and reduced weight B. Improved fuel distribution and redundancy C. Simplicity and cost-effectiveness D. Reduced

Nevelis asked Aug 24, 2024

by Nevelis

7.9k points

1 answer

5 votes

104k views

The use of double convolution bellows is limited to ____ axles (2-164). 1) 2 2) 3 3) 4 4) 164

DeyaEldeen asked Aug 24, 2024

by DeyaEldeen

7.9k points

1 answer

4 votes

183k views

If a vehicle starts to skid on water (hydroplane), the driver should quickly apply the brakes.

Premdeep Mohanty asked Aug 24, 2024

by Premdeep Mohanty

8.2k points

1 answer

4 votes

119k views

The inspector shall: report the type of branch circuit conductors

Iliyass Hamza asked Aug 24, 2024

by Iliyass Hamza

9.3k points

1 answer

2 votes

206k views

At selected locations in the building the piping is connected to a hose. These connections are controlled by _________. No water is allowed into the hose until the valve is opened.

Lxndr asked Aug 24, 2024

by Lxndr

8.4k points

1 answer

3 votes

70.1k views

If you are entering a freeway from a merging lane, who has the right of way?

FrobberOfBits asked Aug 24, 2024

by FrobberOfBits

8.0k points

1 answer

0 votes

121k views

Running M6 T8 command in MDI: a) loads tool#8 in ATC b) loads tool#8 in spindle c) loads tool#8 in spindle then in ATC d) any of the above depending on previous code

Conmadoi asked Aug 24, 2024

by Conmadoi

8.4k points

1 answer

1 vote

196k views

Type W drywall screws must be long enough to penetrate the wood framing how far?

Lorah Attkins asked Aug 24, 2024

by Lorah Attkins

9.0k points

1 answer

3 votes

202k views

When locating a 6" PE OR Steel pipe (service or main), all of the listed markings are required, EXCEPT:

Revive asked Aug 24, 2024

by Revive

7.9k points

1 answer

4 votes

44.2k views

Which of the following cannot be used as a nondestructive testing method for steel castings and forgings? A) radiography B) magnetic particle testing C) ultrasonic testing D) chemical analysis

Tavi asked Aug 24, 2024

by Tavi

8.5k points

1 answer

2 votes

6.6k views

Planing hulls are designed to ride on top of the water and tend to be fast. Displacement hulls tend to push through the water and are typically slower. (TRUE / FALSE)

TheJF asked Aug 24, 2024

by TheJF

8.5k points

1 answer

3 votes

186k views

A single dashed yellow line usually marks the centerline of a two-way roadway where? 1) a vehicle may pass if it is safe. 2) a vehicle may not pass. 3) a vehicle is allowed to park. 4) a vehicle may make

Vladievlad asked Aug 24, 2024

by Vladievlad

8.1k points

1 answer

5 votes

132k views

DM (2 standards for producing one unit of output) A) Cost-Benefit Analysis B) Six Sigma C) Duplication Method D) Efficiency Ratio

Charly Berthet asked Aug 24, 2024

by Charly Berthet

8.6k points

1 answer

3 votes

224k views

Which of the following requires an endorsement on your cdl

Zerg Overmind asked Aug 24, 2024

by Zerg Overmind

8.3k points

1 answer

5 votes

14.0k views

___________ is a type of handsaw that cuts against the grain of the wood?

Radi asked Aug 24, 2024

by Radi

7.4k points

1 answer

4 votes

74.9k views

When you are making a normal left turn (unprotected) what is the last thing you make sure of?

Diego Nieto asked Aug 24, 2024

by Diego Nieto

8.9k points

1 answer

2 votes

28.9k views

Lathing trim accessories include ________. 1) edge beads 2) control joints 3) All of the above 4) corner beads

Jsbeckr asked Aug 24, 2024

by Jsbeckr

8.1k points

1 answer

4 votes

112k views

The two-way road you are driving on has a lane marked as show in the picture. This lane is used:

Cihangir asked Aug 24, 2024

by Cihangir

6.8k points

1 answer

0 votes

87.3k views

What type of hand needle is best suited for installing hidden stitches? 1) Embroidery needle 2) Sharps needle 3) Ballpoint needle 4) Tapestry needle

Taylorsuk asked Aug 24, 2024

by Taylorsuk

8.3k points

1 answer

0 votes

180k views

Directional signs, other than automotive traffic signs, shall be ____________ with a black panel and a white directional symbol. Any additional wording on the sign must be in black letters on the white

Willem Evertse asked Aug 24, 2024

by Willem Evertse

8.5k points

1 answer

5 votes

188k views

Page:

« prev
1
...
892
893
894
895
896
897
898
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions