Recent questions in Engineering

Question

Technician A says that a voltage drop of 0.8 volts on the starter ground circuit is within specifications. Technician B says that high starter draw current could be caused by a spun main bearing in the

Steven Muhr asked Jan 13, 2021

by Steven Muhr

4.6k points

1 answer

0 votes

176k views

Which option identifies the type of system that will be designed in the following scenario? Josh is an engineer who is hired to redesign a chair for the elderly; it is mobile but can also rise up and down

Mateech asked Jan 13, 2021

by Mateech

3.9k points

2 answers

0 votes

127k views

A Turing machine with doubly infinite tape is similar to an ordinary Turing machine, but its tape is infinite to the left as well as to the right. The tape is initially filled with blanks except for the

Benjamin De Bos asked Jan 12, 2021

by Benjamin De Bos

4.2k points

1 answer

4 votes

44.7k views

A roadway with a rough-asphalt pavement has a cross slope of 2%, a longitudinal slope of 2.5%, a curb height of 8 cm, and a 90-cm-wide concrete gutter. If the flow rate in the gutter is 0.07 m/s, determine

Borys Kupar asked Jan 12, 2021

by Borys Kupar

4.6k points

1 answer

3 votes

139k views

Tom is a sound editor and is working on an audio mixer. What feature of the audio mixer should he use to adjust the volume of the audio clip? A. equalizer B. level C. time-based effects D. panning

Kyr Dunenkoff asked Jan 12, 2021

by Kyr Dunenkoff

4.1k points

2 answers

3 votes

120k views

Which operators are required to maintain a proper lookout?

Alex Koshelev asked Jan 12, 2021

by Alex Koshelev

3.9k points

1 answer

5 votes

87.6k views

What is the technique used during the activities definition process that breaks down the "work units" in a work package into smaller and smaller chunks to identify what activities are required to complete

AlvaroAV asked Jan 12, 2021

by AlvaroAV

4.4k points

1 answer

2 votes

187k views

Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to blended. The results are as follows: Aggregate A: Bulk specific gravity 2.491; absorption 0.8% Aggregate

Bazdin asked Jan 12, 2021

by Bazdin

3.9k points

2 answers

2 votes

47.6k views

The piston of a steam engine is S0 cm in diameter, and the maximum steam gage pressure is 1.4 MPa. If the design stress for the piston rod is 68 MPa, its cross-sectional area (m') should be most nearly:

Fidel Castro asked Jan 12, 2021

by Fidel Castro

3.9k points

1 answer

3 votes

19.7k views

A common way of measuring the thermal conductivity of a material is to sandwich an electric thermofoil heater between two identical samples of the material. The thickness of the resistance heater, including

GarDavis asked Jan 12, 2021

by GarDavis

4.1k points

1 answer

2 votes

106k views

Consider a refrigerator that consumes 400 W of electric power when it is running. If the refrigerator runs only one-quarter of the time and the unit cost of electricity is $0.13/kWh, what is the electricity

Abdullah Aziz asked Jan 12, 2021

by Abdullah Aziz

4.6k points

1 answer

1 vote

205k views

A variation of the following biometric authentication protocol was experimentally tested several years ago at immigration checkpoints in major U.S. airports. A user registers in person by showing his credentials

Gorden Gram asked Jan 12, 2021

by Gorden Gram

4.2k points

1 answer

2 votes

64.7k views

For some transformation having kinetics that obey the Avrami equation (Equation 10.17), the parameter n is known to have a value of 1.1. If, after 129 s, the reaction is 50% complete, how long (total time)

AaronHS asked Jan 12, 2021

by AaronHS

4.1k points

1 answer

2 votes

219k views

Based on experimental observations, the acceleration of a particle is defined by the relationa = -( 0.1 + sin(x/b) ),where a and x are expressed in m/s^2 and meters, respectively. Knowing that b = 0.8

Michael Kim asked Jan 12, 2021

by Michael Kim

4.6k points

1 answer

3 votes

10.7k views

Natural gas at and standard atmospheric pressure of 14.7 psi (abs) is compressed isentropically to a new absolute pressure of 70 psi. Determine the final density and temperature of the gas.

Prabhu asked Jan 12, 2021

by Prabhu

4.0k points

1 answer

2 votes

180k views

Rose is building a circuit that accepts sound input and amplifies it. Which component will perform the amplification function? FET transistor ceramic capacitor оооо variable resistor D. LED diode

Akiko asked Jan 12, 2021

by Akiko

3.9k points

1 answer

5 votes

206k views

At steady state, a valve and steam turbine operate in series. The steam flowing through the valve undergoes a throttling process. At the valve inlet, the conditions are 600 lbf/in.2, 800°F. At the valve

Akhi Akl asked Jan 12, 2021

by Akhi Akl

4.6k points

1 answer

5 votes

179k views

A 0.01 m3 piston and cylinder contains an ideal gas at 5.92154 atm, 290 K . A constant pressure process produces 54 kJ of work on the surroundings. What is the final volume of the gas?

Matthew Lowe asked Jan 12, 2021

by Matthew Lowe

4.1k points

1 answer

2 votes

188k views

Software, such as a word processor, search engine, or mobile interface, typically includes plug-in support specific to a language to aid with spelling. In this assignment, you will implement a class that

Thijs Van Dien asked Jan 12, 2021

by Thijs Van Dien

4.2k points

1 answer

1 vote

212k views

What is one way a C47 can be used on set?

Anthonyhumphreys asked Jan 12, 2021

by Anthonyhumphreys

4.5k points

2 answers

4 votes

156k views

Page:

« prev
1
...
843
844
845
846
847
848
849
...
863
next »

Ask a Question

Recent questions in Engineering

Other Questions