Recent questions in Engineering

Question

Decide how the sketches below would be listed, if they were listed in order of decreasing force between the charges. That is, select "1" beside the sketch with the strongest force between the charges,

Nandsito asked Feb 24, 2021

by Nandsito

4.2k points

1 answer

2 votes

91.1k views

A method used to control density and overcrowding by restricting setbacks, building height, or the ratio of open area is known as

Kali Charan Rajput asked Feb 24, 2021

by Kali Charan Rajput

5.3k points

1 answer

0 votes

137k views

Ashley needs to form cubes from the metal sheet. She can use . Jack needs to manufacture a plastic water tank. He can use .

Emperor XLII asked Feb 23, 2021

by Emperor XLII

4.4k points

1 answer

2 votes

63.9k views

What’s the population in the world and why does it keep increasing in bad areas.

Stephane Bersier asked Feb 23, 2021

by Stephane Bersier

4.5k points

2 answers

1 vote

136k views

A plane wall of thickness 2L = 40 mm and thermal conductivity k = 5 W/m K experiences uniform volumetric heat generation at a rate q, while convection heat transfer occurs at both of its surfaces (x =

Michaelslater asked Feb 23, 2021

by Michaelslater

4.8k points

1 answer

3 votes

22.8k views

"A computer architect redesigns the pipeline above to enable branch prediction. When PCSrc is asserted (branch taken) IF/ID is flushed, and speculative instructions are flushed by deasserting some of their

Akash Joshi asked Feb 23, 2021

by Akash Joshi

5.0k points

1 answer

2 votes

228k views

Comparing cold working to hot working, flow stress is usually lower in _____ Question 19 options: Cold working Hot working

Mchr asked Feb 23, 2021

by Mchr

5.0k points

1 answer

1 vote

125k views

The slender bar is moving in general plane motion with the indicated linear and angular properties. Locate the instantaneous center of zero velocity (distances x to the right of G and y above G) and determine

Houda asked Feb 23, 2021

by Houda

4.3k points

1 answer

3 votes

148k views

One pound-mass of water fills a 2.4264-ft3 weighted piston-cylinder device at a temperature of 6008F. The piston- cylinder device is now cooled until its temperature is 2008F. Determine the final pressure

Tony Bourdeaux asked Feb 23, 2021

by Tony Bourdeaux

4.5k points

1 answer

3 votes

126k views

If three-fourths of the marbles in a bag are blue and there are 20 marbles in the bag, how many marbles are NOT blue?

James Menkal asked Feb 23, 2021

by James Menkal

4.6k points

1 answer

1 vote

9.1k views

Toddlers are children from three to four years of age. True False

Sambehera asked Feb 23, 2021

by Sambehera

5.0k points

2 answers

4 votes

133k views

What is the significance of an extension line in an engineering drawing? A. the line shows the limits of a dimension B. the line shows dimensions not used in fabrication C. the line is perpendicular to

Lindsay Landry asked Feb 23, 2021

by Lindsay Landry

4.8k points

2 answers

1 vote

160k views

a) Calculate the modulus of elasticity of carbon-epoxy composite under isostrain condition if the composite consists of 40% carbon fibers and 60% epoxy by volume. Also, b) calculate the percentage of load

Muleskinner asked Feb 23, 2021

by Muleskinner

4.5k points

1 answer

0 votes

205k views

Consider 8.0 kg of austenite containing 0.45 wt% C and cooled to less than 727°C (1341°F). (a) What is the proeutectoid phase? (b) How many kilograms each of total ferrite and cementite form? (c) How many

MatG asked Feb 23, 2021

by MatG

5.0k points

1 answer

3 votes

83.0k views

Given a force of 72 lbs at a distance of 15 ft, calculate the moment produced.

Carra asked Feb 23, 2021

by Carra

5.1k points

1 answer

0 votes

58.5k views

Steam flows steadily through a turbine at a rate of 45,000 lbm/h, entering at 1000 psia and 9008F and leaving at 5 psia as saturated vapor. If the power generated by the turbine is 4 MW, determine the

Longblog asked Feb 23, 2021

by Longblog

5.0k points

1 answer

3 votes

43.9k views

A 5-cm-diameter shaft rotates at 4500 rpm in a 15-cmlong, 8-cm-outer-diameter cast iron bearing (k = 70 W/m·K) with a uniform clearance of 0.6 mm filled with lubricating oil (μ = 0.03 N·s/m2 and k = 0.

Preetha asked Feb 23, 2021

by Preetha

4.4k points

1 answer

4 votes

36.9k views

Water (10 degree C) is flowing at a rate of 0.35 m^3/s, and it is assumed that h_L = 2 V^2/2g from the reservoir to the gage, where V is the velocity in the 30-cm pipe. What power must the pump supply?

Seaneshbaugh asked Feb 23, 2021

by Seaneshbaugh

4.8k points

1 answer

2 votes

53.4k views

Cromium and tantalum both have the BCC crystal structure, and Ta forms a substitutional solid solution for all concentrations at room temperature. Compute the unit cell edge length for a 22 wt% Cr - 78

Tobino asked Feb 23, 2021

by Tobino

4.5k points

1 answer

3 votes

206k views

To purchase a new car, you borrow $20,000. The bank offers a 6-year loan at an interest rate of 3.25% compounded annually. If you make only one payment at the end of the loan period, repaying the principal

Purush Pawar asked Feb 23, 2021

by Purush Pawar

4.2k points

1 answer

4 votes

44.8k views

Page:

« prev
1
...
826
827
828
829
830
831
832
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions