menu
QAmmunity.org
Recent questions in Engineering
Login
Register
My account
Edit my Profile
Private messages
My favorites
Recent questions in Engineering
Ask a Question
Questions
Unanswered
Tags
Categories
Ask a Question
Recent questions in Engineering
The elevation knob adjusts the point of aim for the M16A2 Rifle how much?
Maxime Fabre
asked
Sep 5, 2024
by
Maxime Fabre
8.9k
points
Engineering
college
1
answer
0
votes
206k
views
A welding supervisor under CSA Standard W47.1 shall have a minimum of how many years of experience, assuming no reduction has been granted based on education and experience? a. 3 years b. 5 years c. 7
Juri
asked
Sep 5, 2024
by
Juri
7.9k
points
Engineering
college
1
answer
3
votes
124k
views
What forms a hairpin loop?
Adis
asked
Sep 5, 2024
by
Adis
7.9k
points
Engineering
college
1
answer
5
votes
129k
views
What license is required to operate a moped? What is the maximum speed you may operate a moped?
Liviu
asked
Sep 5, 2024
by
Liviu
8.6k
points
Engineering
college
1
answer
5
votes
224k
views
Six pieces of lumber measure 1" x 8" x 14' What is the total board footage? 56 84 1/2 672 112 1/3
Naghal
asked
Sep 5, 2024
by
Naghal
8.5k
points
Engineering
college
1
answer
2
votes
1.0k
views
In the shears over comb method, holding the comb flat against the head will?
Rashomon
asked
Sep 5, 2024
by
Rashomon
7.9k
points
Engineering
college
1
answer
1
vote
148k
views
When driving through a work zone, it is a good safety practice to? 1) Slow down and obey all posted speed limits 2) Pay attention to signs and flaggers 3) Merge well before the lane closure 4) All of the
Dan Simon
asked
Sep 5, 2024
by
Dan Simon
8.5k
points
Engineering
college
1
answer
4
votes
145k
views
It is important for driving safety to always be looking ahead. Which of the following is NOT a recommended time/distance that you should be looking ahead? 1) 2 to 3 seconds 2) 1 to 2 blocks 3) half a mile
Margaret Bloom
asked
Sep 5, 2024
by
Margaret Bloom
9.0k
points
Engineering
college
1
answer
0
votes
227k
views
Which of the following determinants of an organization's structure describes the way an organization transfers inputs into outputs? A) strategy B) environment C) investment D) size E) technology
Sadije
asked
Sep 5, 2024
by
Sadije
8.6k
points
Engineering
college
1
answer
1
vote
80.0k
views
Where is the proper grade fuel for a specific engine listed?
Xavier Lowmiller
asked
Sep 5, 2024
by
Xavier Lowmiller
7.9k
points
Engineering
college
1
answer
3
votes
135k
views
Approximately how long does it take a new driver to reach the driving ability of an experienced driver?
Dundee MT
asked
Sep 5, 2024
by
Dundee MT
7.9k
points
Engineering
college
1
answer
3
votes
183k
views
Which method of steering provides less chance of injury in a crash when a vehicle is equipped with an airbag? A) Placing your hands at the 10 and 2 o'clock positions on the steering wheel. B) Placing your
Erik Vullings
asked
Sep 5, 2024
by
Erik Vullings
8.0k
points
Engineering
college
1
answer
0
votes
36.5k
views
Close-range application of water to the fire is the objective of which type of operation? 1) Rescue operation 2) Salvage operation 3) Fire suppression operation 4) Ventilation operation
Gotomanners
asked
Sep 5, 2024
by
Gotomanners
7.3k
points
Engineering
college
1
answer
2
votes
170k
views
What type of boats are required to carry one Type IV throwable device?
Nick Friesen
asked
Sep 5, 2024
by
Nick Friesen
9.1k
points
Engineering
college
1
answer
4
votes
17.3k
views
With the acceleration depicted in Fig. 2, a particle travels along a straight path. Plot the v-t and x-t curves for 0 < 150 < 15s. If the particle starts from the origin with an initial velocity of vo = -14 m/s, calculate (a) the particle's maximum velocity and (b) the particle's maximum position coordinate.
Suneet Bansal
asked
Sep 5, 2024
by
Suneet Bansal
8.3k
points
Engineering
college
1
answer
5
votes
169k
views
What is the definition of Type III Concrete? 1) Moderate / Low sulfate resistance 2) High sulfate resistance 3) High early strength - early set 4) Low heat of hydration
Tyeisha
asked
Sep 5, 2024
by
Tyeisha
8.8k
points
Engineering
college
1
answer
1
vote
182k
views
(a).Compare the characteristics of reciprocating and rotary compressors. (b) Explain factors to be considered in the selection of compressors.
Paggas
asked
Sep 5, 2024
by
Paggas
8.1k
points
Engineering
college
1
answer
4
votes
125k
views
When rigging a bundle of pipe or tubing, which hitch would provide the best contact between sling and load? 1) Basket Hitch 2) Choker Hitch 3) Vertical Hitch 4) Double Wrap Hitch
XpertSiji
asked
Sep 5, 2024
by
XpertSiji
8.3k
points
Engineering
college
1
answer
4
votes
226k
views
Slow vehicles should use the left-hand lane exceot when passing or making a left turn. True False
Fernando Echeverria
asked
Sep 5, 2024
by
Fernando Echeverria
7.5k
points
Engineering
college
1
answer
2
votes
166k
views
What is the reference that provides minimum construction requirements for fencing?
Admir
asked
Sep 5, 2024
by
Admir
8.0k
points
Engineering
college
1
answer
5
votes
113k
views
Page:
« prev
1
...
819
820
821
822
823
824
825
...
1000
...
next »
Ask a Question
Welcome to QAmmunity.org, where you can ask questions and receive answers from other members of our community.
9.5m
questions
12.2m
answers
Other Questions
How do you can you solve this problem 37 + y = 87; y =
What is .725 as a fraction
Compare and contrast an electric generator and a battery??
What goal of the constitution was also a goal of the Magna Carta?
is it true or false that after the american revolution conflicts in the northwest territory erupted between remaining british soldiers and native americans
Search QAmmunity.org