Recent questions in Engineering

Question

Proper handling of blueprints includes which of the following A.Folding plans neatly after use B. Using plans to wipe off hands C. Allowing anyone to mark-up the plans D. None of the above

Don Bottstein asked Mar 18, 2021

by Don Bottstein

5.5k points

1 answer

1 vote

173k views

A cylinder of length L would be made to carry a torque T with an angle of twist ɸ. There are two options considered: 1) hollowed cylinder with an inner radius that is equal to 0.9 of the outer radius,

Elzo Valugi asked Mar 18, 2021

by Elzo Valugi

5.4k points

1 answer

1 vote

190k views

A large plate is fabricated from a steel alloy that has a plane strain fracture toughness of 82.4 M P a m. If the plate is exposed to a tensile stress of 345 MPa during service use, determine the minimum

Nbkhope asked Mar 18, 2021

by Nbkhope

4.9k points

2 answers

0 votes

40.1k views

Which of the following is a valid statement about a resume ?

Dan Radu asked Mar 18, 2021

by Dan Radu

5.3k points

2 answers

2 votes

130k views

A box of 30 diodes is known to contain five defective ones. If two diodes are selected at random without replacement, what is the probability that at least one of these diodes is defective?

Akash Tantri asked Mar 18, 2021

by Akash Tantri

5.3k points

1 answer

2 votes

129k views

Choose the best explanation below for why dimensional analysis is also sometimes referred to as the factor label approach. Select the correct answer below: O It is sometimes called the factor label approach

Daniel Coffman asked Mar 18, 2021

by Daniel Coffman

4.9k points

1 answer

4 votes

118k views

Design a riprap-lined trapezoidal channel that has a capacity of 1000 cfs and slope of 0.0005 ft/ft. Crushed rock is to be used and the channel bottom with is not to exceed 15 ft. Determine the riprap

ErTR asked Mar 18, 2021

by ErTR

6.1k points

1 answer

5 votes

222k views

To calculate the maximum allowable stresses in pressure vessels, compute the minimum allowable thickness of pressure vessels to meet certain constraints, and observe and compare properties of different

Accuya asked Mar 18, 2021

by Accuya

5.2k points

2 answers

2 votes

7.8k views

A spherical gas container made of steel has a(n) 13-ft outer diameter and a wall thickness of 0.375 in. Knowing that the internal pressure is 60 psi, determine the maximum normal stress and the maximum

Richardwestenra asked Mar 18, 2021

by Richardwestenra

5.5k points

1 answer

5 votes

105k views

Who is responsible for keeping your facility in compliance

Steve Nyholm asked Mar 18, 2021

by Steve Nyholm

4.9k points

1 answer

0 votes

182k views

The displacement volume of an internal combustion engine is 2.2 liters. The processes within each cylinder of the engine are modeled as an air-standard Diesel cycle with a cutoff ratio of 2.5. The state

Comrade Che asked Mar 18, 2021

by Comrade Che

4.7k points

1 answer

3 votes

178k views

I need help plz and thank you this is do As we learned in the Lesson, many choirs post videos of their performances on the internet. For this assignment, you will find two recordings of the same choir

Pablouche asked Mar 18, 2021

by Pablouche

5.7k points

2 answers

3 votes

47.6k views

An engineer must design a rectangular box that has a volume of 9 m3 and that has a bottom whose length is twice its width. What are the dimensions of the box so that the total surface area (of all six

Tanushree asked Mar 18, 2021

by Tanushree

5.6k points

1 answer

2 votes

217k views

Which is an alloy made up of iron and carbon and has high compressive and tensile strength? A. glass B. concrete C. steel D. wood

Kelloti asked Mar 18, 2021

by Kelloti

5.0k points

2 answers

1 vote

90.4k views

Determine the minimum radius of a horizontal circular curve for a route having a 70 mph design speed, super-elevation (e) 3%, and coefficient of side friction 0.12. (b) Determine the degree of curve using

Epistemologist asked Mar 17, 2021

by Epistemologist

5.6k points

1 answer

0 votes

107k views

If outside of the flask is not dry when first determination is made and it is dried for second determination, what effect will that have on your result?

Victor Wang asked Mar 17, 2021

by Victor Wang

5.4k points

1 answer

4 votes

230k views

Which of the following expression yields an integer between 0 and 100, inclusive? A. (int)(Math.random() * 100 + 1) B. (int)(Math.random() * 101) C. (int)(Math.random() * 100) D. (int)(Math.random() *

Vinita asked Mar 17, 2021

by Vinita

5.6k points

1 answer

3 votes

42.3k views

A fluid particle flowing along a stagnation streamline, as shown in Video V4.9 and Fig. P4.35, slows down as it approaches the stagnation point. Measurements of the dye flow in the video indicate that

Wolfcow asked Mar 17, 2021

by Wolfcow

5.2k points

2 answers

0 votes

172k views

Describe the general guidelines in creating rough sketches.

Eanticev asked Mar 17, 2021

by Eanticev

4.9k points

1 answer

0 votes

168k views

The article provides information by using a list. What does it list? A. Thanksgiving food B. places where clams can be found C. birds served at the first Thanksgiving D. four men who went on a "fowling"

Estel asked Mar 17, 2021

by Estel

4.8k points

1 answer

5 votes

215k views

Page:

« prev
1
...
793
794
795
796
797
798
799
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions