Recent questions in Engineering

Question

Solutions to avoid dumpster diving threats?

Tom Womack asked Dec 21, 2024

by Tom Womack

8.3k points

1 answer

1 vote

134k views

What is the single focal point for UTC and UDM requirements? 1) UTC 2) UDM 3) Both UTC and UDM 4) None of the above

Robertkroll asked Dec 21, 2024

by Robertkroll

8.3k points

1 answer

3 votes

228k views

What should be displayed in the boiler room? a) vacation schedule b) engineer's license, and exemption or inspection certificates c) the manufacturers book of operation on the boiler

Anikhan asked Dec 21, 2024

by Anikhan

7.8k points

1 answer

1 vote

174k views

technician a says that the oil pump is driven directly by the crankshaft. technician b says on some older engines the oil pump is driven by the distributor. who is correct?

Andrei T asked Dec 21, 2024

by Andrei T

8.2k points

1 answer

2 votes

136k views

The ________ protects the starter motor from damage if the ignition switch is held in the start position after the engine starts.

Rhorvath asked Dec 21, 2024

by Rhorvath

8.3k points

1 answer

4 votes

30.1k views

3 types of pipe reamers A. Rotary, Spiral, Tapered B. Manual, Electric, Pneumatic C. Inside, Outside, Cone D. Straight, Spiral, Expanding

Ardenne asked Dec 21, 2024

by Ardenne

7.8k points

1 answer

3 votes

92.7k views

Drill bits can only cut with their ends ("lips") whereas enmills can cut with both their ends and their sides. True or False?

Nayiaw asked Dec 21, 2024

by Nayiaw

7.7k points

1 answer

5 votes

185k views

Speed limit OUTSIDE of thickly settled areas/business district?

Zac asked Dec 21, 2024

by Zac

8.7k points

1 answer

3 votes

112k views

Check the exhaust system regularly to prevent leaks

Dima Malenko asked Dec 21, 2024

by Dima Malenko

8.2k points

1 answer

4 votes

139k views

When there's a shared center lane, you can: 1) Use this lane as a driving lane during rush hour. 2) Drive in this lane as far as necessary, as long as you're turning left. 3) Drive in this lane if you

Abhash Kumar Singh asked Dec 21, 2024

by Abhash Kumar Singh

8.5k points

1 answer

1 vote

101k views

What type of fittings may be used with steel pipe? a. Threaded Fittings b. Welded Fittings c. Flanged Fittings d. Grooved Fittings

Denia asked Dec 21, 2024

by Denia

8.7k points

1 answer

0 votes

140k views

PARA is used to show destination. A. True B. False

Skwiggs asked Dec 21, 2024

by Skwiggs

7.0k points

1 answer

3 votes

93.9k views

Where and how could you use a switch made out of aluminum foil or copper tape?

Tobspr asked Dec 21, 2024

by Tobspr

7.5k points

2 answers

2 votes

173k views

What must be filled out when there is not Automated Passport Control Kiosk available at your arriving destination?

Dsomnus asked Dec 21, 2024

by Dsomnus

8.3k points

1 answer

4 votes

46.0k views

A temporary substitute vehicle is not a covered auto if used to substitute for which of the following? A Owned trailer B Recently purchased van C An owned car D Rental car

Anand Dwivedi asked Dec 21, 2024

by Anand Dwivedi

8.4k points

1 answer

2 votes

55.4k views

Which of the following is NOT a comparison operator symbol? 1) = 2) ≠ 3) < 4) ≥

Bic asked Dec 21, 2024

by Bic

7.4k points

1 answer

2 votes

23.0k views

(APU limits) normal operating EGT is approximately ___C

Gfppaste asked Dec 21, 2024

by Gfppaste

7.9k points

1 answer

5 votes

107k views

________________ (Always, sometimes, never) signal lane changes

Sid Steward asked Dec 21, 2024

by Sid Steward

8.2k points

1 answer

4 votes

113k views

The flexural tensile bond strength of a masonry wall is relevant in:_______

Rob Anderson asked Dec 21, 2024

by Rob Anderson

6.7k points

1 answer

5 votes

212k views

What is a notch made in a rafter with an overhang so that the rafter will fit against a plate?

Michael Richards asked Dec 21, 2024

by Michael Richards

8.1k points

1 answer

2 votes

105k views

Page:

« prev
1
...
59
60
61
62
63
64
65
...
1000
...
next »

Ask a Question

Recent questions in Engineering

Other Questions